Saturday 19 October 2013
Tuesday 24 September 2013
1-855-wanna-reno? - Chimney repair : repointing the mortar
Chimney repair : repointing the mortar 1855wannareno.com
Its wise have your chimney inspected by
an expert to check and know if the bricks are broken within.
It is not uncommon for brick chimneys
to crumble with age. Chimneys are typically positioned in exposed
areas of the roof, and crumbling will occur attributable to
weathering albeit alternative masonry around your house is in
physical fitness. In most cases, a crumbling chimney means that the
mortar between the bricks did get out the joints, the bricks did
crack, or both. Repair a chimney that has began to crumble could be a
task most householders will do themselves. typically it needs you to
mix the mortar and replace any broken bricks.
.jpg)
1
Measure the length of the broken
irregular bricks within the chimney. Bricks that are custom-cut would
force you to chop the new brick to suit.
2
Mark the measuring of the recent bricks
on your new brick employing a marker.
3
Put on safety glasses and work gloves.
Chip a groove on the lines you marked within the brick employing a
set chisel and a hammer.
4
Insert a brick set into the groove, and
strike the tip with the hammer to separate the brick at your mark.
Continue cutting the remaining bricks within the same manner.
5
Chisel out the mortar round the broken
brick to a depth of a minimum of 1/2 in., exploitation the hammer and
chisel. Move the chime in on the joint, removing one of the mortar
at a time. Make sure to clean properly the joints with a wire brush
as you\'re employed.
6
Pull every brick because it loosens
from the chimney and set it aside. don\'t take away too several
bricks from the chimney at only once. Instead, repair the chimney bit
by bit, removing solely a few of bricks at a time. Once one space is
repaired, it\'ll support the structure as you tackle consecutive.
7
Mix your mortar in step with the
manufacturer’s label directions. build just enough to figure for
fifteen to twenty minutes at a time.
8
Dampen the brick with a sponge. Apply
the mortar into the empty areas in a very layer that\'s an equivalent
thickness as adjacent joints.
9
Trowel a layer of mortar onto the
highest and ends of the replacement brick, and place the brick into
the mortared house.
10
Scrape away excess mortar with the
trowel. form the wet mortar with the trowel so it matches the looks
of the adjacent joints.
11
Continue applying mortar into the gaps
or sections and replace the brick till all the broken bricks are
replaced.
12
Allow the mortar to dry for regarding
Associate in Nursing hour. Wipe the surplus mortar from the
encircling brick with a humid sponge.
Repointing Crumbling Mortar
1
Chisel cracked or crumbling mortar from
the joints with a hammer and set chisel. Clean every joint of loose
mortar and dirt with a wire brush.
2
Mix your mortar in step with the
manufacturer’s label directions. build just enough to figure for
fifteen to twenty minutes at a time. Usually, mortar is mixed at a
quantitative relation of two components sand to one half cement.
Water is another till you deliver the goods a pasty consistency.
3
Pour the mortar into a mortar bag.
Place the mortar into the clean out joints, and squeeze to push the
mortar through the nozzle to fill the joint.
4
Scrape the surplus mortar from the
chimney employing a trowel, and form it therefore it matches the
adjacent joints.
5
Allow the mortar to dry for regarding
Associate in Nursing hour. Wipe the surplus mortar from the
encircling brick with a humid sponge.
Things You can want
Ladder
Measuring tape
Marker
Safety glasses
Gloves
Hammer
Cold chisel
Brick set
Bucket
Mortar mix
Water
Trowel
Wire brush
Mortar bag
Sponge
Wednesday 4 September 2013
1-855-wanna-reno? - EXTERIOR PAINTING : FACTS THAT YOU NEED TO CONSIDER
1-855-wanna-reno? - EXTERIOR PAINTING : FACTS THAT YOU NEED TO CONSIDER
YOU have to.... Buy sensible Brushes..
First, let’s state selecting paint brushes. don\'t obtain low-cost brushes. They won’t do a satisfactory job, and plenty of of those brushes shed bristles into your paint as you\'re employed. you\'ve got to pay some cash on sensible brushes, however if properly cared for they’ll last a period. Expect to pay between $12 and $22 for a high quality brush. And don’t obtain the angular sash brushes. They’re fine for painting windows, however not for the majority of the work that you’re doing. For latex paints, an artificial brush ought to be used. sponsor least 2, flat head, a pair of ½-inch artificial brushes for applying water-base paint. China or Chinese bristle brushes area unit required if applying oil base paint.
You have to......Use the correct Paint
Next, let’s state what kind of end coat to use. For years, oil base paint was thought of to be the simplest selection and thought to carry up well. Over time this has been tried to not be true, and a latex semi-gloss paint is that the pro’s selection. you\'ve got to see that paint exists on the surfaces you’ll be painting, whether or not it’s oil or latex. Moisten a clean rag with fermentation alcohol and rub the surface of the paint.. If the prevailing paint is oil base, you either got to use oil base paint, or seal the surface with associate degree oil base primer/sealer and paint over with latex semi-gloss paint. That’s what I’d do. It holds up far better, and clean-up is simple with heat water. it\'s troublesome to scrub up brushes accustomed apply oil base paint, and needs lots of paint diluent, that could be a dangerous material, and so is difficult to lose.
You can use disposable brushes to use the primer/sealer. They’re rock bottom and area unit diversely known as “chip brushes” or “sealer brushes.”
Don’t Go so fast!
Before you are doing something, you ought to power wash the complete exterior space to be painted. Over my a few years as knowledgeable painter, I 1st power washed any exterior surfaces i used to be about to paint. you would like the new coats to stick to the wall, to not accumulated dirt or mildew on the surface. you\'ll notice info on power laundry here. Before applying the primer/sealer, end your power laundry and scrape and sand any in the altogether areas, then simply wash the house down with a hosepipe to get rid of any sanding dirt. Let it dry, and you\'re able to apply the sealer.
Caulking is extremely necessary. All cracks and holes ought to be sealed with a latex caulk. seal on all trim and around window and door frames. I actually have been complemented on the sweetness of my finished paint comes over the years. Customers say my job appearance most higher than alternative painters, and that they don’t recognize why, they simply assume i\'m a much better painter than most. It’s primarily as a result of I seal everything. It makes for a special, lovely finished job.
Get the proper combination
Now, let’s state “boxing” the paint. Regardless if you get a 5-gallon will, or several 1-gallon cans, you wish a minimum of a pair of empty metal gallon cans with lids to use for boxing and as “cut cans.” First, coat the complete inside the empty cans with associate degree oil base primer/sealer. Semi-gloss paints can return off of the edges of wills and deposit themselves within the can, deed lumps or flakes behind. thus don’t use a paint will that hasn’t been ready with flat oil base sealer. If you would like to use unspecified empty semi-gloss cans, soak them in plight 1st, and take away all paint to the blank metal surface, and seal them rather like a replacement will.
Let the cans dry within the wind and sun till you\'re certain they\'re 100% dry. Open all gallon cans of paint and pour them back and forth between cans and your 2 empty cans. this can be boxing the paint. it\'s necessary as a result of all paint these days is tinted {and will|and will} vary in shade and color from will to can. By boxing you insure uniform paint color across your whole job.
Don’t lay your paint brush across the highest of the gallon will. it\'ll drip paint and dry up. And don’t dip and so scrape your coat the open will either. Use a cut will to figure with, and place your cut brush directly into the 2 inches of paint that you just confine your operating cut will. That keeps your paint clean, your job neat and your brush freed from dried paint.
Pay Attention
A house with wood siding has got to be painted each five years typically, and each metal and vinyl siding have to be compelled to be painted ever fifteen to twenty years. the various sides of the house fade otherwise from uneven sun exposure, that the facet of the house that receives the foremost sun are going to be a unique color. Take that under consideration after you choose your color.
I created a killing painting metal siding once vinyl siding 1st came out, as a result of the metal siding was pale to a unique color on each facet and therefore the vinyl looked good. and that i was in business long enough to color pale vinyl siding. With even these sturdy siding materials desirous to be repainted, that’s one more reason for owners to come back to doityourself.com to be told the way to paint, and save the expense of hiring a painting contractor.
The sun matters whereas you’re doing the work too. It’s tempting to choose a fine looking, sunny day to figure outside, however you’re more contented with some overcast. an excessive amount of sun and warmth dries your paint too quick, and you\'ll find yourself with uneven coverage if you’re not careful. Of course, it may be not possible to search out the right day. simply keep in mind to figure quicker within the heat and keep track of how briskly the paint is drying behind you.
Make Sure You pack up
For cleanup of brushes employed in latex base painting, use many heat water and a wire brush. confirm to induce the paint out of the “heel” or base of the comb. Spin the comb by chop-chop rolling it between your hands. To store the comb, comb it with the wire brush and store it within the paper cowl it came with. once you’re able to use the comb once more, comb it out with the wire brush. If you lose the paper cowl, wrap the comb in adhesive tape, however confirm to get rid of the tape future day and comb the bristles with a wire brush. this can be however a high quality brush lasts for years.
Painting is one amongst those tasks that take a moment to be told and years to master. nobody will simply tell you the way to chop an honest line, the way to rescue a drying drip, or the way to estimate what quantity paint you wish to hide a stucco wall vs. a wood wall of constant size on associate degree eighty two degree day with low humidness. These area unit stuff you got to develop a compassionate. however if you follow my tips, and listen to the fundamentals, you ought to be ready to do an honest job, whether or not you’re covering one area wall, or painting your whole house.
For more info contact us at www.1855wannareno.com
YOU have to.... Buy sensible Brushes..
First, let’s state selecting paint brushes. don\'t obtain low-cost brushes. They won’t do a satisfactory job, and plenty of of those brushes shed bristles into your paint as you\'re employed. you\'ve got to pay some cash on sensible brushes, however if properly cared for they’ll last a period. Expect to pay between $12 and $22 for a high quality brush. And don’t obtain the angular sash brushes. They’re fine for painting windows, however not for the majority of the work that you’re doing. For latex paints, an artificial brush ought to be used. sponsor least 2, flat head, a pair of ½-inch artificial brushes for applying water-base paint. China or Chinese bristle brushes area unit required if applying oil base paint.
You have to......Use the correct Paint
Next, let’s state what kind of end coat to use. For years, oil base paint was thought of to be the simplest selection and thought to carry up well. Over time this has been tried to not be true, and a latex semi-gloss paint is that the pro’s selection. you\'ve got to see that paint exists on the surfaces you’ll be painting, whether or not it’s oil or latex. Moisten a clean rag with fermentation alcohol and rub the surface of the paint.. If the prevailing paint is oil base, you either got to use oil base paint, or seal the surface with associate degree oil base primer/sealer and paint over with latex semi-gloss paint. That’s what I’d do. It holds up far better, and clean-up is simple with heat water. it\'s troublesome to scrub up brushes accustomed apply oil base paint, and needs lots of paint diluent, that could be a dangerous material, and so is difficult to lose.
You can use disposable brushes to use the primer/sealer. They’re rock bottom and area unit diversely known as “chip brushes” or “sealer brushes.”
Don’t Go so fast!
Before you are doing something, you ought to power wash the complete exterior space to be painted. Over my a few years as knowledgeable painter, I 1st power washed any exterior surfaces i used to be about to paint. you would like the new coats to stick to the wall, to not accumulated dirt or mildew on the surface. you\'ll notice info on power laundry here. Before applying the primer/sealer, end your power laundry and scrape and sand any in the altogether areas, then simply wash the house down with a hosepipe to get rid of any sanding dirt. Let it dry, and you\'re able to apply the sealer.
Caulking is extremely necessary. All cracks and holes ought to be sealed with a latex caulk. seal on all trim and around window and door frames. I actually have been complemented on the sweetness of my finished paint comes over the years. Customers say my job appearance most higher than alternative painters, and that they don’t recognize why, they simply assume i\'m a much better painter than most. It’s primarily as a result of I seal everything. It makes for a special, lovely finished job.
Get the proper combination
Now, let’s state “boxing” the paint. Regardless if you get a 5-gallon will, or several 1-gallon cans, you wish a minimum of a pair of empty metal gallon cans with lids to use for boxing and as “cut cans.” First, coat the complete inside the empty cans with associate degree oil base primer/sealer. Semi-gloss paints can return off of the edges of wills and deposit themselves within the can, deed lumps or flakes behind. thus don’t use a paint will that hasn’t been ready with flat oil base sealer. If you would like to use unspecified empty semi-gloss cans, soak them in plight 1st, and take away all paint to the blank metal surface, and seal them rather like a replacement will.
Let the cans dry within the wind and sun till you\'re certain they\'re 100% dry. Open all gallon cans of paint and pour them back and forth between cans and your 2 empty cans. this can be boxing the paint. it\'s necessary as a result of all paint these days is tinted {and will|and will} vary in shade and color from will to can. By boxing you insure uniform paint color across your whole job.
Don’t lay your paint brush across the highest of the gallon will. it\'ll drip paint and dry up. And don’t dip and so scrape your coat the open will either. Use a cut will to figure with, and place your cut brush directly into the 2 inches of paint that you just confine your operating cut will. That keeps your paint clean, your job neat and your brush freed from dried paint.
Pay Attention
A house with wood siding has got to be painted each five years typically, and each metal and vinyl siding have to be compelled to be painted ever fifteen to twenty years. the various sides of the house fade otherwise from uneven sun exposure, that the facet of the house that receives the foremost sun are going to be a unique color. Take that under consideration after you choose your color.
I created a killing painting metal siding once vinyl siding 1st came out, as a result of the metal siding was pale to a unique color on each facet and therefore the vinyl looked good. and that i was in business long enough to color pale vinyl siding. With even these sturdy siding materials desirous to be repainted, that’s one more reason for owners to come back to doityourself.com to be told the way to paint, and save the expense of hiring a painting contractor.
The sun matters whereas you’re doing the work too. It’s tempting to choose a fine looking, sunny day to figure outside, however you’re more contented with some overcast. an excessive amount of sun and warmth dries your paint too quick, and you\'ll find yourself with uneven coverage if you’re not careful. Of course, it may be not possible to search out the right day. simply keep in mind to figure quicker within the heat and keep track of how briskly the paint is drying behind you.
Make Sure You pack up
For cleanup of brushes employed in latex base painting, use many heat water and a wire brush. confirm to induce the paint out of the “heel” or base of the comb. Spin the comb by chop-chop rolling it between your hands. To store the comb, comb it with the wire brush and store it within the paper cowl it came with. once you’re able to use the comb once more, comb it out with the wire brush. If you lose the paper cowl, wrap the comb in adhesive tape, however confirm to get rid of the tape future day and comb the bristles with a wire brush. this can be however a high quality brush lasts for years.
Painting is one amongst those tasks that take a moment to be told and years to master. nobody will simply tell you the way to chop an honest line, the way to rescue a drying drip, or the way to estimate what quantity paint you wish to hide a stucco wall vs. a wood wall of constant size on associate degree eighty two degree day with low humidness. These area unit stuff you got to develop a compassionate. however if you follow my tips, and listen to the fundamentals, you ought to be ready to do an honest job, whether or not you’re covering one area wall, or painting your whole house.
For more info contact us at www.1855wannareno.com
Tuesday 27 August 2013
1-855-wanna-reno? - VINYL SIDING: ISSUES TO CONSIDER
1-855-wanna-reno? GET YOUR HOME RENOVATED!
VINYL SIDING: ISSUES TO CONSIDER
Vinyl siding issues became nightmares for associate degree increasing variety of house owners. although this siding material is extremely standard, it\'s vital for consumers to remember of the drawbacks and environmental dangers it poses. many of us suppose that vinyl siding could be a one-time, maintenance-free installation. However, as time goes by, they persuade be wrong. Below square measure a number of the foremost common drawbacks of vinyl siding.
a – Unappealing as compared to Wood or Stone
Vinyl siding is accessible in several colours and textures. It will simulate the design of wood terribly closely. However, a discerning eye will quickly work out the distinction between authentic and pretend wood. notwithstanding however well it\'s created and put in, vinyl siding will ne\'er be as authentic as wood or stone.
b – It Can free Toxins at High Temperatures
Vinyl siding could be a product that\'s beneath constant criticism from environmental organizations. it\'s a plastic material that\'s factory-made in associate degree environmentally risky manner. the top product is additionally deadly at high temperatures. If it catches hearth, it will expose folks inside to high amounts of poisons.
c – It Fades in Few Years
Vinyl siding is accessible in many alternative worth ranges and qualities. the most affordable ones square measure most liable to weakening and discoloration. when many years, you may notice that the siding has lost its attractiveness and you\'ll got to replace it.
d – will Crack or Bend struggling
Vinyl siding may be broken once hit by objects or if you mistakenly push the snow-blower or lawn tool against it. Cracks and different kinds of injury can not be repaired simply. you\'ll got to replace the broken a part of the siding, which may be sophisticated as a result of it\'s troublesome to seek out precise matches.
e – needs Regular improvement
Vinyl siding can accumulate mud, mildew and mildew when a while outside. If left unattended, these issues will invade your home. Annual improvement of vinyl siding could be a demand, contrary to standard conception that it\'s maintenance-free.
f – will Hide wetness issues
Vinyl siding may be liable to wetness issues if you employ pressure washers or clean the siding improperly. wetness beneath the siding will quickly invade your home and result in mildew, cracking paint and broken wallpaper.
g – Inadequate Insulation
Vinyl siding doesn\'t supply sensible insulation. Newer styles of the siding material return put in with foam, that offers higher insulation. However, most vinyl sidings need extra backup once it involves insulation.
h – skimpy Color selections
Vinyl siding will crack and bend out of form if it\'s exposed to high temperatures. as a result of dark colours absorb additional heat, vinyl sidings square measure sometimes found solely in lighter shades.
i – Lowers Property worth
Vinyl siding doesn\'t enhance property worth, not like wood, stucco or stone. It may be unattractive to several consumers, particularly in upmarket neighborhoods.
j – unhealthy selections for old Homes
Vinyl siding will injury the charm and original attractiveness of historic homes. The installation method could need changes and might even injury the underlying structure.
If you need siding installation or more info visit www.1855wannareno.com
Monday 26 August 2013
1-855-wanna-reno? | CHIMNEYS : WATER THE WORST ENEMY
1-855-wanna-reno? Get your home reovated!
IMPORTANT issues about CHIMNEYS
Water causes additional harm to masonry chimneys than hearth. trust it for an instant. All the brick and different materials that frame your home are protected by the roof and eave, all that\'s, except your chimney. The chimney courageously sticks up on top of the roof perpetually exposed to the weather.
A masonry chimney is built of a range of masonry and metal materials, together with brick, mortar, tile, steel and forged iron. All of those materials can suffer accelerated deterioration as a results of prolonged contact with water.
Masonry materials deteriorate quickly once exposed to the freeze/thaw method within which wetness that has penetrated the materials sporadically freezes and expands, inflicting undue stress. Water within the chimney conjointly causes rust in steel and forged iron, weakening or destroying the metal components.
Water will cause damage inside and outside of your home and masonry chimney including.
Following ar the four main ways that to stop water harm.
.jpg)
Chimney Cap
Chimney caps, conjointly referred to as rain covers, ar most likely the foremost cheap precautions that a house owner will use to stop water penetration and harm to the chimney. Chimneys have one or additional giant openings (flues) at the highest that collect rain water and funnel it on to the chimney interior. A strong, elegant cap not solely keeps this water out, however also will stop birds and animals from getting into and nesting within the chimney.
Caps conjointly perform as spark arrestors, preventing sparks from landing on the roof or different near fuel.
Fix a broken Chimney Crown
The chimney crown, conjointly named because the chimney wash, is that the prime part of a masonry chimney. It covers and seals the highest of the chimney from the flue liners to the chimney edge. Most masonry chimneys ar engineered with associate degree inadequate crown made from common mortar combine, a similar mixture wont lay the bricks of the chimney. This mortar isn\'t designed for and can not face up to years of weather abuse while not cracking, break or deteriorating; things that permit water to penetrate in between the bricks.
A proper chimney crown ought to be made of a hydraulic cement based mostly mixture associate degreed forged or fashioned therefore it provides an overhang, or drip edge, projected on the far side all sides of the chimney by a minimum of 2 inches. This drip edge directs the runoff from the crown off from the perimeters of the chimney, serving to stop erosion of the brick and mortar within the chimney\'s vertical surfaces.
There are some trendy waterproof, non-shrinking, cement like coatings for repairing broken mortar crowns that appear to figure fine.
Replace Flashing
Flashing is that the seal between the building material and also the chimney. Flashing prevents rain water from running down the chimney into living areas wherever it will harm ceilings or walls, or cause rot in rafters, joists, or different structural components. the foremost effective flashing is formed of 2 components, the flashing and also the counter- flashing.
The base flashing is associate degree L formed piece of metal extending up the chimney facet and beneath the roofing shingles. The counter flashing, that overlaps the bottom flashing, is imbedded and sealed within the chimney\'s masonry joints. This 2 part flashing permits each the roof and also the chimney to expand or contract at their own rates while not breaking the waterproof lock in either space.
Waterproof Your Chimney
Most masonry materials ar porous and can absorb giant amounts of water. Common brick is sort of a sponge, gripping water and wicking wetness to the chimney interior. Defective mortar joints or the utilization of improper mortar or brick will greatly increase the tendency to soak up and convey water to the inside of the masonry chimney structure.
Several merchandise are developed specifically to be used as waterproofing agents on masonry chimneys. These formulas ar vapor pervious which suggests that they permit the chimney to respire, but not in. so water that has penetrated the chimney, or wetness that has originated from within, is allowed to flee, whereas the waterproofing agent prevents water from getting into from the skin.
Paint, or any non vapor pervious water sealer, ought to ne\'er be used as a waterproofing agent as a result of it\'ll lure wetness within the chimney, fast deterioration.
Water harm to masonry chimneys is sometimes a slow, delicate method. the matter is commonly not evident till it\'s become quite serious.
Although these water interference measures might value many bucks , they\'ll prevent the most important expense of huge masonry repairs or reconstruction of the complete chimney within the not too distant future, and per se represent a wise investment in your home
If you need chimney repair or maintenance please visit us www.1855wannareno.com
IMPORTANT issues about CHIMNEYS
Water causes additional harm to masonry chimneys than hearth. trust it for an instant. All the brick and different materials that frame your home are protected by the roof and eave, all that\'s, except your chimney. The chimney courageously sticks up on top of the roof perpetually exposed to the weather.
A masonry chimney is built of a range of masonry and metal materials, together with brick, mortar, tile, steel and forged iron. All of those materials can suffer accelerated deterioration as a results of prolonged contact with water.
Masonry materials deteriorate quickly once exposed to the freeze/thaw method within which wetness that has penetrated the materials sporadically freezes and expands, inflicting undue stress. Water within the chimney conjointly causes rust in steel and forged iron, weakening or destroying the metal components.
Water will cause damage inside and outside of your home and masonry chimney including.
Following ar the four main ways that to stop water harm.
Chimney Cap
Chimney caps, conjointly referred to as rain covers, ar most likely the foremost cheap precautions that a house owner will use to stop water penetration and harm to the chimney. Chimneys have one or additional giant openings (flues) at the highest that collect rain water and funnel it on to the chimney interior. A strong, elegant cap not solely keeps this water out, however also will stop birds and animals from getting into and nesting within the chimney.
Caps conjointly perform as spark arrestors, preventing sparks from landing on the roof or different near fuel.
Fix a broken Chimney Crown
The chimney crown, conjointly named because the chimney wash, is that the prime part of a masonry chimney. It covers and seals the highest of the chimney from the flue liners to the chimney edge. Most masonry chimneys ar engineered with associate degree inadequate crown made from common mortar combine, a similar mixture wont lay the bricks of the chimney. This mortar isn\'t designed for and can not face up to years of weather abuse while not cracking, break or deteriorating; things that permit water to penetrate in between the bricks.
A proper chimney crown ought to be made of a hydraulic cement based mostly mixture associate degreed forged or fashioned therefore it provides an overhang, or drip edge, projected on the far side all sides of the chimney by a minimum of 2 inches. This drip edge directs the runoff from the crown off from the perimeters of the chimney, serving to stop erosion of the brick and mortar within the chimney\'s vertical surfaces.
There are some trendy waterproof, non-shrinking, cement like coatings for repairing broken mortar crowns that appear to figure fine.
Replace Flashing
Flashing is that the seal between the building material and also the chimney. Flashing prevents rain water from running down the chimney into living areas wherever it will harm ceilings or walls, or cause rot in rafters, joists, or different structural components. the foremost effective flashing is formed of 2 components, the flashing and also the counter- flashing.
The base flashing is associate degree L formed piece of metal extending up the chimney facet and beneath the roofing shingles. The counter flashing, that overlaps the bottom flashing, is imbedded and sealed within the chimney\'s masonry joints. This 2 part flashing permits each the roof and also the chimney to expand or contract at their own rates while not breaking the waterproof lock in either space.
Waterproof Your Chimney
Most masonry materials ar porous and can absorb giant amounts of water. Common brick is sort of a sponge, gripping water and wicking wetness to the chimney interior. Defective mortar joints or the utilization of improper mortar or brick will greatly increase the tendency to soak up and convey water to the inside of the masonry chimney structure.
Several merchandise are developed specifically to be used as waterproofing agents on masonry chimneys. These formulas ar vapor pervious which suggests that they permit the chimney to respire, but not in. so water that has penetrated the chimney, or wetness that has originated from within, is allowed to flee, whereas the waterproofing agent prevents water from getting into from the skin.
Paint, or any non vapor pervious water sealer, ought to ne\'er be used as a waterproofing agent as a result of it\'ll lure wetness within the chimney, fast deterioration.
Water harm to masonry chimneys is sometimes a slow, delicate method. the matter is commonly not evident till it\'s become quite serious.
Although these water interference measures might value many bucks , they\'ll prevent the most important expense of huge masonry repairs or reconstruction of the complete chimney within the not too distant future, and per se represent a wise investment in your home
If you need chimney repair or maintenance please visit us www.1855wannareno.com
Saturday 24 August 2013
1-855-wanna-reno? | Eavestrough : Could it damage our roof and foundation?
1-855-wanna-reno? The object of the Eavestrough
The primary job is to gather fresh water because it flows down your roof and so direct it to the downspout wherever it\'s harmlessly deposited your yard or into the storm sewer.
Water can forever follow the trail of effort. The gutters area unit put in at a grade to assist the water flow to the downspout. If this easy system is not operating properly, water will backup onto your roof. there\'s no easier thanks to injury your roof than to permit water to pool on prime of the shingles. If the shingles are not already broken by wind, weather and time, then having puddles of standing water on prime of them may be a surefire thanks to shorten their lifespans. this is often wherever correct maintenance of your gutters comes into play.
Nature working... 1-855-wanna-reno?
Mother Nature actually enjoys her cycles, and each year trees shed their leaves for winter so that they will grow them once more return spring. the bulk of the leaves fall to the bottom, however some fall onto the roof and into the gutters. The water currently has resistance to flow. once enough leaves constitute the gutter, it cannot continue with the flow of water and this could cause pooling.
It does not take long for leaves to fully impede water flow, and that they will even clog the downspout, which suggests no water is exploit the roof because it ought to. At best, the water currently flows over the sting of the gutters, which may be terrible for your foundation, however that is another article. At worst, the water currently flows the opposite manner and begins to pool on the roof. In winter time, this could cause Associate in Nursing ice dam, with every ordered wave of physical change and thawing shoving a wedge of ice deeper below your shingles.
Every year, I take a glance at my gutters. i am lucky therein I will see them through the windows of my second story, except for those in ranch vogue homes, then you\'ll ought to get out the ladder and create a visible review. do not wait till the gutters area unit fully clogged before cleanup. Instead, create it a daily a part of your yearly maintenance.
Some heavily timbered areas might needed cleanup a minimum of double each year.
Eavestrough cleaning . 1-855-wanna-reno?
If the gutters haven\'t been clean in a very long term, then the primary time goes to be back breaking work. you will need a combine of significant work gloves, a study ladder, trowel, box of garbage luggage and a minimum of one free afternoon.
Start on the corner of the house and set the open box of garbage luggage on the roof. Pull out one amongst the baggage and start to fill it with junk. If it\'s simply leaves, then use your hands. If the junk is significant and soaked with water, then use the trowel to dig out the junk.
Place it within the garbage luggage till they\'re concerning 0.5 full or fill plastic searching luggage instead. Throw down the baggage into the yard and choose them up once you are done. This keeps you from perpetually increasing and down the ladder. If the junk is lightweight, then the cleanup will not take long to try to to.
The eavestrough area typically neglected a part of yearly maintenance, however they directly contribute to the period of time of the roof, not to mention your foundation, therefore you should consider always to keep them in good shape.
If you need eavestrough installation,leafguard, clean up or repair please contact us at www.1855wannareno.com
follow us on www.facebook.com/1855wannareno or
www.twitter.com/1855wannareno
Wednesday 21 August 2013
1-855-wanna-reno? - SOLAR SHINGLES: Future of roofing?
1-855-wanna-reno? - SOLAR SHINGLES: Future of roofing?
The price purpose and power generation of shingles with imbedded photovoltic cells has finally reached constant level as ancient solar panels. That’s one thing they’ve been chasing for years. This solar cell product is slowly rising in new homes and older roof replacements, and will doubtless boost alternative energy installations. Despite the technology’s blessings, it’s still not wide touted or offered, nor sky-high embraced by energy professionals.
Advantages -
Solar shingles work just like the larger star panels that ar currently dotting several rooftops. Their main advantage is that they\'re additional esthetically pleasing than the typically monstrous roof installations that some home-owner associations and housing authorities forbid.
Instead of an enormous array, solar shingles integrate simply with existing roof shingles via bolt-on panels. Their costs, though\' once above larger electrical phenomenon installations, are dropping and turning into additional competitive due to innovations in technology.
The chemical giant’s shingles generate concerning twelve watts of power per square-foot and might be connected to your home’s grid to remit excess power to the electrical company and generate revenue to offset its initial price.
Installation
An practised professional will install solar shingles, however you\'ll seemingly want facilitate from associate degree linesman to line up the wiring to your home’s grid. Estimates for installation vary from $6,000 to $10,000, however owners ought to note that federal tax credits are offered for installations, and a some governments might supply incentives furthermore.
Availability
The problem is accessibility. Despite being introduced in 2005, star shingles ar still offered solely during a few locations, and even industrial large companies are not mass-producing them.
Still, several energy professionals ostensibly aren\'t attentive to the star shingle potential, or see the requirement to be discomposed with deviating from established installations of larger panels.
Follow us on www.facebook.com/1855wannareno
Visit our web at www.1855wannareno.com
The price purpose and power generation of shingles with imbedded photovoltic cells has finally reached constant level as ancient solar panels. That’s one thing they’ve been chasing for years. This solar cell product is slowly rising in new homes and older roof replacements, and will doubtless boost alternative energy installations. Despite the technology’s blessings, it’s still not wide touted or offered, nor sky-high embraced by energy professionals.
 |
| Solar shingles |
Advantages -
Solar shingles work just like the larger star panels that ar currently dotting several rooftops. Their main advantage is that they\'re additional esthetically pleasing than the typically monstrous roof installations that some home-owner associations and housing authorities forbid.
Instead of an enormous array, solar shingles integrate simply with existing roof shingles via bolt-on panels. Their costs, though\' once above larger electrical phenomenon installations, are dropping and turning into additional competitive due to innovations in technology.
The chemical giant’s shingles generate concerning twelve watts of power per square-foot and might be connected to your home’s grid to remit excess power to the electrical company and generate revenue to offset its initial price.
Installation
An practised professional will install solar shingles, however you\'ll seemingly want facilitate from associate degree linesman to line up the wiring to your home’s grid. Estimates for installation vary from $6,000 to $10,000, however owners ought to note that federal tax credits are offered for installations, and a some governments might supply incentives furthermore.
Availability
The problem is accessibility. Despite being introduced in 2005, star shingles ar still offered solely during a few locations, and even industrial large companies are not mass-producing them.
Still, several energy professionals ostensibly aren\'t attentive to the star shingle potential, or see the requirement to be discomposed with deviating from established installations of larger panels.
Follow us on www.facebook.com/1855wannareno
Visit our web at www.1855wannareno.com
Tuesday 20 August 2013
1-855-wanna-reno? Painting our home : Exterior painting (1855wannareno.com)
EXTERIOR PAINTING
GET RENOVATED WITH US !!! 11-855-wanna-reno?
sensible Brushes
First, let’s point out selecting paint brushes. don't purchase low cost brushes. They won’t do a satisfactory job, and lots of of those brushes shed bristles into your paint as you're employed. you have got to pay some cash on sensible brushes, however if properly cared for they’ll last a time period. Expect to pay between $12 and $22 for a top quality brush. And don’t purchase the angular sash brushes. They’re fine for painting windows, however not for the majority of the work that you’re doing. For latex paints,an artificial brush ought to be used. support least 2, flat head, a pair of ½-inch artificial brushes for applying rubber-base paint. China or Chinese bristle brushes square measure required if applying oil base paint.
the proper Paint
Next, let’s point out what variety of end coat to use. For years, oil base paint was thought-about to be the most effective alternative and thought to carry up well. Over time this has been tried to not be true, and a latex semi-gloss paint is that the pro’s alternative. you have got to see that paint exists on the surfaces you’ll be painting, whether or not it’s oil or latex. Moisten a clean rag with ethanol and rub the surface of the paint. If some paint rubs off it’s latex, if not it’s oil base. If the prevailing paint is oil base, you either got to use oil base paint, or seal the surface with Associate in Nursing oil base primer/sealer and paint over with latex semi-gloss paint. That’s what I’d do. It holds up far better, and clean-up is straightforward with heat water. it's tough to scrub up brushes wont to apply oil base paint, and needs lots of paint agent, that may be a unsafe material, and so is difficult to get rid of.
You can use disposable brushes to use the primer/sealer. They’re the bottom and square measure diversely known as “chip brushes” or “sealer brushes.”
Don’t try to go so fast
Before you are doing something, you must power wash the whole exterior space to be painted. Over my a few years as an expert painter, I 1st power washed any exterior surfaces i used to be aiming to paint. you wish the new coats to stick to the wall, to not accumulated dirt or mildew on the surface. you'll be able to notice info on power laundry here. Before applying the primer/sealer, end your power laundry and scrape and sand any naked as a jaybird areas, then simply wash the house down with ahosepipe to get rid of any sanding dirt. Let it dry, and you're able to apply the sealer.
Caulking is incredibly vital. All cracks and holes ought to be calked with a latex caulk. calk on all trim and around window and door frames. I actually have been complemented on the sweetness of my finished paint comes over the years. Customers say my job appearance such a lot higher than alternative painters, and that they don’t recognize why, they solely suppose i'm a higher painter than most. It’s principally as a result of I calk everything. It makes for a special, stunning finished job.
Get the Right one
Now, let’s point out “boxing” the paint. Regardless if you purchase a 5-gallon will, or several 1-gallon cans, you would like a minimum of a pair of empty metal gallon cans with lids to use for boxing and as “cut cans.” First, coat the whole inside the empty cans with Associate in Nursing oil base primer/sealer. Semi-gloss paints can come back off of the perimeters of wills and deposit themselves within the can, feat lumps or flakes behind. thus don’t use a paint will that hasn’t been set with flat oil base sealer. If you wish to use unspecified empty semi-gloss cans, soak them in predicament 1st, and take away all paint to the blank metal surface, and seal them a bit like a brand new will.
Let the cans dry within the wind and sun till you're positive they're 100% dry. Open all gallon cans of paint and pour them back and forth between cans and your 2 empty cans. this can be boxing the paint. it's necessary as a result of all paint these days is tinted {and will|and will} vary in shade and color from will to can. By boxing you insure uniform paint color across your whole job.
Don’t lay your paint brush across the highest of the gallon will. it'll drip paint and dry up. And don’t dip so scrape your coat the open will either. Use a cut will to figure with, and place your cut brush directly into the 2 inches of paint that you simply detain your operating cut will. That keeps your paint clean, your job neat and your brush freed from dried paint.
Attention to the sides
A house with wood siding has got to be painted each five years typically, and each Al and vinyl siding ought to be painted ever fifteen to twenty years. the various sides of the house fade otherwise from uneven sun exposure, therefore the aspect of the house that receives the foremost sun are a special color. Take that under consideration once you choose your color.
I created a killing painting Al siding once vinyl siding 1st came out, as a result of the Al siding was light to a special color on each aspect and therefore the vinyl looked good. and that i was in business long enough to color light vinyl siding. With even these sturdy siding materials wanting to be repainted, that’s one more reason for householders to come back to doityourself.com to find out the way to paint, and save the expense of hiring a painting contractor.
The sun matters whereas you’re doing the duty too. It’s tempting to choose a fine looking, sunny day to figure outside, however you’re happier with some overcast. an excessive amount of sun and warmth dries your paint too quick, and you'll be able to find yourself with uneven coverage if you’re not careful. Of course, it may be not possible to search out the right day. simply keep in mind to figure quicker within the heat and keep track of how briskly the paint is drying behind you.
shut down
For cleanup of brushes utilized in latex base painting, use many heat water and a wire brush. make certain to induce the paint out of the “heel” or base of the comb. Spin the comb by chop-chop rolling it between your hands. To store the comb, comb it with the wire brush and store it within the paper cowl it came with. once you’re able to use the comb once more, comb it out with the wire brush. If you lose the paper cowl, wrap the comb in adhesive tape, however make certain to get rid of the tapeconsecutive day and comb the bristles with a wire brush. this can be however a top quality brush lasts for years.
Painting is one among those tasks that take a second to find out and years to master. nobody will simply tell you the way to chop a decent line, the way to rescue a drying drip, or the way to estimate what proportion paint you would like to hide a stucco wall vs. a wood wall of an equivalent size on Associate in Nursing eighty two degree day with low wetness. These square measure stuff you got to develop a compassionate. however if you follow my tips, and concentrate to the fundamentals,you must be ready to do a decent job, whether or not you’re covering one area wall, or painting your whole house.
follow us on www/facebook.com/1855wannareno
GET RENOVATED WITH US !!! 11-855-wanna-reno?
sensible Brushes
First, let’s point out selecting paint brushes. don't purchase low cost brushes. They won’t do a satisfactory job, and lots of of those brushes shed bristles into your paint as you're employed. you have got to pay some cash on sensible brushes, however if properly cared for they’ll last a time period. Expect to pay between $12 and $22 for a top quality brush. And don’t purchase the angular sash brushes. They’re fine for painting windows, however not for the majority of the work that you’re doing. For latex paints,an artificial brush ought to be used. support least 2, flat head, a pair of ½-inch artificial brushes for applying rubber-base paint. China or Chinese bristle brushes square measure required if applying oil base paint.
the proper Paint
Next, let’s point out what variety of end coat to use. For years, oil base paint was thought-about to be the most effective alternative and thought to carry up well. Over time this has been tried to not be true, and a latex semi-gloss paint is that the pro’s alternative. you have got to see that paint exists on the surfaces you’ll be painting, whether or not it’s oil or latex. Moisten a clean rag with ethanol and rub the surface of the paint. If some paint rubs off it’s latex, if not it’s oil base. If the prevailing paint is oil base, you either got to use oil base paint, or seal the surface with Associate in Nursing oil base primer/sealer and paint over with latex semi-gloss paint. That’s what I’d do. It holds up far better, and clean-up is straightforward with heat water. it's tough to scrub up brushes wont to apply oil base paint, and needs lots of paint agent, that may be a unsafe material, and so is difficult to get rid of.
You can use disposable brushes to use the primer/sealer. They’re the bottom and square measure diversely known as “chip brushes” or “sealer brushes.”
Don’t try to go so fast
Before you are doing something, you must power wash the whole exterior space to be painted. Over my a few years as an expert painter, I 1st power washed any exterior surfaces i used to be aiming to paint. you wish the new coats to stick to the wall, to not accumulated dirt or mildew on the surface. you'll be able to notice info on power laundry here. Before applying the primer/sealer, end your power laundry and scrape and sand any naked as a jaybird areas, then simply wash the house down with ahosepipe to get rid of any sanding dirt. Let it dry, and you're able to apply the sealer.
Caulking is incredibly vital. All cracks and holes ought to be calked with a latex caulk. calk on all trim and around window and door frames. I actually have been complemented on the sweetness of my finished paint comes over the years. Customers say my job appearance such a lot higher than alternative painters, and that they don’t recognize why, they solely suppose i'm a higher painter than most. It’s principally as a result of I calk everything. It makes for a special, stunning finished job.
Get the Right one
Now, let’s point out “boxing” the paint. Regardless if you purchase a 5-gallon will, or several 1-gallon cans, you would like a minimum of a pair of empty metal gallon cans with lids to use for boxing and as “cut cans.” First, coat the whole inside the empty cans with Associate in Nursing oil base primer/sealer. Semi-gloss paints can come back off of the perimeters of wills and deposit themselves within the can, feat lumps or flakes behind. thus don’t use a paint will that hasn’t been set with flat oil base sealer. If you wish to use unspecified empty semi-gloss cans, soak them in predicament 1st, and take away all paint to the blank metal surface, and seal them a bit like a brand new will.
Let the cans dry within the wind and sun till you're positive they're 100% dry. Open all gallon cans of paint and pour them back and forth between cans and your 2 empty cans. this can be boxing the paint. it's necessary as a result of all paint these days is tinted {and will|and will} vary in shade and color from will to can. By boxing you insure uniform paint color across your whole job.
Don’t lay your paint brush across the highest of the gallon will. it'll drip paint and dry up. And don’t dip so scrape your coat the open will either. Use a cut will to figure with, and place your cut brush directly into the 2 inches of paint that you simply detain your operating cut will. That keeps your paint clean, your job neat and your brush freed from dried paint.
Attention to the sides
A house with wood siding has got to be painted each five years typically, and each Al and vinyl siding ought to be painted ever fifteen to twenty years. the various sides of the house fade otherwise from uneven sun exposure, therefore the aspect of the house that receives the foremost sun are a special color. Take that under consideration once you choose your color.
I created a killing painting Al siding once vinyl siding 1st came out, as a result of the Al siding was light to a special color on each aspect and therefore the vinyl looked good. and that i was in business long enough to color light vinyl siding. With even these sturdy siding materials wanting to be repainted, that’s one more reason for householders to come back to doityourself.com to find out the way to paint, and save the expense of hiring a painting contractor.
The sun matters whereas you’re doing the duty too. It’s tempting to choose a fine looking, sunny day to figure outside, however you’re happier with some overcast. an excessive amount of sun and warmth dries your paint too quick, and you'll be able to find yourself with uneven coverage if you’re not careful. Of course, it may be not possible to search out the right day. simply keep in mind to figure quicker within the heat and keep track of how briskly the paint is drying behind you.
shut down
For cleanup of brushes utilized in latex base painting, use many heat water and a wire brush. make certain to induce the paint out of the “heel” or base of the comb. Spin the comb by chop-chop rolling it between your hands. To store the comb, comb it with the wire brush and store it within the paper cowl it came with. once you’re able to use the comb once more, comb it out with the wire brush. If you lose the paper cowl, wrap the comb in adhesive tape, however make certain to get rid of the tapeconsecutive day and comb the bristles with a wire brush. this can be however a top quality brush lasts for years.
Painting is one among those tasks that take a second to find out and years to master. nobody will simply tell you the way to chop a decent line, the way to rescue a drying drip, or the way to estimate what proportion paint you would like to hide a stucco wall vs. a wood wall of an equivalent size on Associate in Nursing eighty two degree day with low wetness. These square measure stuff you got to develop a compassionate. however if you follow my tips, and concentrate to the fundamentals,you must be ready to do a decent job, whether or not you’re covering one area wall, or painting your whole house.
follow us on www/facebook.com/1855wannareno
Subscribe to:
Posts (Atom)